key features: 1w output power miniature sip case dual isolated outputs 1,000 vdc isolation >2 mhour mtbf 24 standard models industry standard pin-out micropower direct 232 tosca drive stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com d100d m i n i a t u r e , 1 w s i p miniature, 1w sip d u a l i s o l a t e d o u t p u t dual isolated output d c / d c c o n v e r t e r s dc/dc con vert ers series electrical speci? cations speci? cations typical @ +25c, nominal input voltage & rated output current, unless otherwise noted. speci? cations subject to change without notice. input parameter conditions min. typ. max. units input voltage range 5 vdc input 4.5 5.0 5.5 vdc 12 vdc input 10.8 12.0 13.2 24 vdc input 21.6 24.0 26.4 48 vdc input 43.2 48.0 52.8 input filter internal capacitor reverse polarity input current 0.3 a output parameter conditions min. typ. max. units output voltage accuracy 3.0 % line regulation for vin change of 1% 1.2 % load regulation iout = 20% to 100% 8.0 ripple & noise (20 mhz) see note 2 75 mv p - p output power protection 120 % temperature coef? cient 0.01 0.02 %/oc output short circuit momentary (0.5 sec.) general parameter conditions min. typ. max. units isolation voltage, input/output 60 seconds 1,000 vdc isolation voltage, output/output 1,000 vdc isolation resistance 500 vdc 1,000 m isolation capacitance 100 khz, 1v 60 pf switching frequency 125 khz environmental parameter conditions min. typ. max. units operating temperature range ambient -40 +25 +85 oc operating temperature range case -40 +90 oc storage temperature range -40 +125 oc cooling free air convection humidity rh, non-condensing 95 % physical case size ( 5v, 12v & 24v input models) 0.76 x 0.24 x 0.37 inches (19.5 x 6.0 x 9.5 mm) case size (48v input models) 0.76 x 0.28 x 0.37 inches (19.5 x 7.2 x 9.5 mm) case material non-conductive black plastic (ul94-v0) weight 0.07 oz (2.1g) reliability speci? cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25oc, gnd benign 2.0 mhours absolute maximum ratings parameter conditions min. typ. max. units input voltage surge (1 sec) 5 vdc input -0.7 9.0 vdc 12 vdc input -0.7 18.0 24 vdc input -0.7 30.0 48 vdc input -0.7 55.0 lead temperature 1 .5 mm from case for 10 sec 260 oc internal power dissipation all models 450 mw caution: exceeding absolute maximum ratings may damage the module. these are not continuous operating ratings. .com .com .com 4 .com u datasheet
notes: all dimensions are typical in inches (mm) tolerance x.xx = 0.01 ( 0.25) pin 1 is marked by a dot or indentation on the side of the unit for 5v, 12v & 24v input models, w = 0.24 in (6.0 mm) for 48v input models, w = 0.28 in (7.2 mm) notes: 1. output load regulation is speci? ed for a load change of 20% to 100%. 2. when measuring output ripple, it is recommended that an external ceramic capacitor (approx 10 f) be placed across the output . 3. the 5v, 12v and 24v input units do not require external components to operate, but the use of an input capacitor (10 f) may enhance performance in some applications. an output capacitor (1.0 f to 10 f) may be used to reduce ripple. the 48v input models require an input capacitor of 4.7 uf to 47 uf (dependent upon the application). 4. it is recommended that a fuse be used on the input of a power supply for protection. see the table above for the correct rating. derating curve -40 -10 0 5 15 25 35 45 55 65 75 85 95 105 0 20 40 60 80 100 ambient temperature 1 c o utput power % 0.02 (0.50) 0.01 (0.25) 0.77 (19.5) 7 6 12 0.08 (2.13) 0.10 (2.54) 0.37 (9.5) 0.12 (3.05) 0.05 (1.25) bottom side w 0.20 (5.08) 0.02 (0.50) 45 0.02 ( 0.50 ) micropower direct www.micropowerdirect.com 232 tosca drive stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com model selection guide mechanical dimensions pin connections model number input output 1 output 2 ef? ciency (%, typ) fuse rating slow-blow (ma) voltage (vdc) current (ma) voltage (vdc) current (ma, max) current (ma, min) voltage (vdc) current (ma, max) current (ma, min) nominal range full-load no-load d101d 5 4.5 - 5.5 277 30 5.0 100.0 10.0 5.0 100.0 10.0 72 500 d102d 5 4.5 - 5.5 266 30 5.0 100.0 10.0 3.3 100.0 10.0 71 500 d103d 5 4.5 - 5.5 260 30 5.0 100.0 10.0 12.0 42.0 4.2 77 500 d104d 5 4.5 - 5.5 250 30 12.0 42.0 4.2 12.0 42.0 4.2 80 500 d105d 5 4.5 - 5.5 244 30 5.0 100.0 10.0 15.0 33.0 3.3 82 500 d106d 5 4.5 - 5.5 256 30 15.0 33.0 3.3 15.0 33.0 3.3 78 500 d111d 12 10.8 - 13.2 116 12 5.0 100.0 10.0 5.0 100.0 10.0 72 200 d112d 12 10.8 - 13.2 117 12 5.0 100.0 10.0 3.3 100.0 10.0 71 200 d113d 12 10.8 - 13.2 108 12 5.0 100.0 10.0 12.0 42.0 4.2 77 200 d114d 12 10.8 - 13.2 104 12 12.0 42.0 4.2 12.0 42.0 4.2 80 200 d115d 12 10.8 - 13.2 108 12 5.0 100.0 10.0 15.0 33.0 3.3 77 200 d116d 12 10.8 - 13.2 107 12 15.0 33.0 3.3 15.0 33.0 3.3 78 200 d121d 24 21.6 - 26.4 58 7 5.0 100.0 10.0 5.0 100.0 10.0 72 100 d122d 24 21.6 - 26.4 59 7 5.0 100.0 10.0 3.3 100.0 10.0 71 100 d123d 24 21.6 - 26.4 54 7 5.0 100.0 10.0 12.0 42.0 4.2 77 100 d124d 24 21.6 - 26.4 52 7 12.0 42.0 4.2 12.0 42.0 4.2 80 100 d125d 24 21.6 - 26.4 54 7 5.0 100.0 10.0 15.0 33.0 3.3 77 100 d126d 24 21.6 - 26.4 53 7 15.0 33.0 3.3 15.0 33.0 3.3 78 100 d131d 48 43.2 - 52.8 29 6 5.0 100.0 10.0 5.0 100.0 10.0 72 100 D132d 48 43.2 - 52.8 30 6 5.0 100.0 10.0 3.3 100.0 10.0 71 100 d133d 48 43.2 - 52.8 27 6 5.0 100.0 10.0 12.0 42.0 4.2 77 100 d134d 48 43.2 - 52.8 26 6 12.0 42.0 4.2 12.0 42.0 4.2 80 100 d135d 48 43.2 - 52.8 26 6 5.0 100.0 10.0 15.0 33.0 3.3 82 100 d136d 48 43.2 - 52.8 27 6 15.0 33.0 3.3 15.0 33.0 3.3 78 100 pin function 1+vin 2-vin 4 +vout 1 5 -vout 1 6 +vout 2 7 -vout 2 output 1 f max output 2 f max 100 100 capacitive load t 1 +v in -v in input filter & switching transistors output rectifier & filter output rectifier & filter block diagram .com .com .com 4 .com u datasheet
|
